LED pull out kitchen mixer tap

Specification

Features

· We promise that our faucets fit your hose since we make our products with standard dimensions and send you standard accessories to make sure your faucet is installed properly.

· The construction of our faucets is ceramic cartridge, which has been proved to be the best method to avoid leaking. The service life of valve can attain to more than 600,000 times.

· All the products have been performed with 1.6Mpa high water pressure test before delivery to ensure each product with absolute quality.

· All of our products are ready in our warehouse and can be shipped out in 7 days.

We guarantee our promise that your faucets will always get to you on time

· Order Processing Time: 3 working days

· Shipping Time: 5-7working days

Image Details

Please kindly note image below is just for your reference.
Different faucets are shipped with different accessories.

A:Hose

B:Other accessories for fixture

Tools You Need for Installation

· Adjustable wrench

· Tape

· Screwdriver

· Flashlight

General Faucet Installation Instruction

Please kindly note that this is just a general instruction, each faucet you buy from us has installation instruction with details inside package.

Step 1: Position the Faucet

A: Begin installing your faucet by placing the gasket and faucet in position on the sink.

B: From under the sink, thread the plastic mounting nuts onto the faucet shanks. Be sure the large side of each plastic mounting nut is up.

C: From the top of the sink, check the faucet and gasket position.

D: From under the sink tighten the mounting nuts, making certain not to over-tighten which could damage the nuts and make them difficult to remove in the future.

Step 2: Attach the Water Supply Tubes

A: Wrap the threads of the water-supply valve with Teflon tape. Although most plumbers use only Teflon tape, some plumbing supply manufacturers also recommend using plumber?s putty.

B: Thread the water supply nut onto the shut-off valve. Tighten the nut with a wrench.

C: Wrap the threads on the faucet shank with Teflon tape, and then thread the water supply nut onto the faucet shank.

D: Tighten the nut with a wrench.

Step 3: Connect the Faucet Lift Rod

A-1: From the top of the sink, insert the lift-rod into the faucet.

A-2: From under the sink, make sure the pivot-rod is in the down position. Insert the lift-rod into the lift-rod strap. Tighten the screw.

B-1: From the top of the sink, make sure the lift-rod opens and closes the drain plug as desired.

B-2: Make any needed adjustments by loosening the lift-rod strap screw and repositioning the lift-rod.

B-3: If you need to connect the lift-rod strap to the pivot rod, slide one end of the spring clip onto the pivot-rod.

B-4: Make sure that both the pivot -rod and the lift-rod are in the down position. Insert the pivot-rod in the closest hole in the lift-rod strap.

B-5: Slide the other end of the pivot-rod. Make sure the lift-rod opens and closes the drain plug as desired.

C-1: Make minor adjustments by loosening the lift-rod strap screw and repositioning the lift-rod.

C-2: Make major adjustments by removing the spring clip and moving the pivot-rod to a different hole in the lift-rod strap.

Step 4: Flush the Faucet

A-1: Anytime you work on plumbing, filings, chips, and other debris can fall into the plumbing pipes.

A-2: This debris can damage the sealing surfaces inside the faucet and cause leaks.

A-3: Remove aerator and black sealing gasket above it.

A-4: Before turning on the water supply, make sure the faucet handles are open (on position) in order to remove the debris without causing damage.

B: Open both water supply valves under the sink.

C-1: Allow the water to run for 15 seconds.

C-2: Close the faucet handles (turn off).

D: Make sure any debris is cleaned from the aerator screen.

E: Replace the aerator.